CJ-series Controller Link Units CJ1W-CLK

International Standards

• The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, and CE: EC Directives.
• Contact your OMRON representative for further details and applicable conditions for these standards.

Controller Link Units

Unit clas- sifica- tion	Product name	Specifications				No. of unit numbers allocated	Current consumption (A)		Model	Stand- ards
		Communi- cations cable	Communi- cations type	Duplex support	Max. Units mountable per CPU Unit		5 V DC	24 V DC
CJ1 CPU Bus Unit	Controller Link Unit	Wired shielded twisted-pair cable *	Data links and message service	No	8	1	0.35	---	CJ1W-CLK23	UC1, N, L, CE

Note: This unit cannot be used with the Machine Automation Controller NJ-series. 
* Use the following special cable for shielded, twisted-pair cable. 
  • ESVC0.5×2C-13262 (Bando Electric Wire: Japanese Company) 
  • ESNC0.5×2C-99-087B (JMACS Japan Co., Ltd.: Japanese Company) 
  • ESPC 1P×0.5mm² (Nagaoka Electric Wire Co.,Ltd.: Japanese Company) 
  • Li2Y-FCY2×0.56qmm (Kromberg & Schubert, Komtec Department: German Company) 
  • 1×2×AWG-20PE+Tr.CUSN+PVC (Draka Cables Industrial: Spanish Company) 
  • #9207 (Belden: US Company)

Accessories

There is no accessory for the CJ series Controller Link Unit.

Controller Link Support Boards

Product name	Specifications		Accessories	Model	Standards
	Communications cable	Communications type
Controller Link Support Board for PCI Bus	Wired shielded twisted-pair cable	Data links and message service	CD-ROM x 1 * INSTALLATION GUIDE (W467) x 1 Communications connector x 1	3G8F7-CLK23-E	CE

* The CD-ROM contains the following software. 
  • Controller Link (PCI) Driver 
  • FinsGateway Version 2003 (PCI-CLK Edition) 
  • FinsGateway Version 3 (PCI-CLK Edition) 
  • Setup Diagnostic Utility 
  • C Library

Repeater Units

Name	Specifications	Model	Standards
Controller Link Repeater Unit	Wire-to-Wire Model	CS1W-RPT01	UC1, CE
	Wire-to-Optical (H-PCF) Model *1	CS1W-RPT02
	Wire-to-Optical (GI) Model *2	CS1W-RPT03

Using Repeater Units enables T-branches and long-distance wiring for Wired Controller Link networks, 62-node configurations, and converting part of the network to optical cable. 
*1. When using wire-to-optical (H-PCF) cable, use a H-PCF cable (for both Controller Link and SYSMAC LINK) or a H-PCF 
       optical fiber cable with connector. 
*2. When using wire-to-optical (GI) cable, use a GI optical cable (for Controller Link).

Relay Terminal Block

Name	Specifications	Model	Standards
Relay Terminal Block for Wired Controller Link Units	Used for Wired Controller Link Units (set of 5)	CJ1W-TB101	---

Controller Link Units can be replaced without stopping the communications of the entire network if a Relay Terminal Block is installed in advance on the Unit in a Wired Controller Link network. Relay Terminal Blocks cannot be used on Controller Link Support Boards.

H-PCF Cables and Optical Connectors

Name		Application/construction		Specifications		Model	Standards
Optical Fiber Cables		Controller Link, SYSMAC LINK, SYSBUS	1. Optical fiber single-core cord 2. Tension member (plastic-sheathed wire) 3. Filler (plastic) 4. Filler surrounding signal wires (plastic, yarn, or fiber) 5. Holding tape (plastic) 6. Heat-resistant PV sheath	Two-core optical cable with tension member	Black 10 m	S3200-HCCB101	---
					Black 50 m	S3200-HCCB501
					Black 100 m	S3200-HCCB102
					Black 500 m	S3200-HCCB502
					Black 1000 m	S3200-HCCB103
					Orange 10 m	S3200-HCCO101
					Orange 50 m	S3200-HCCO501
					Orange 100 m	S3200-HCCO102
					Orange 500 m	S3200-HCCO502
					Orange 1000 m	S3200-HCCO103
Optical Connectors (Crimp-cut)		CS1W-RPT02		Half lock		S3200-COCF2571
				Full lock		S3200-COCF2071

H-PCF Optical Fiber Cables with Connectors (Black Composite Cables with Two-Optical Lines and Two Power Supply Lines)

Application	Appearance	Model	Standards
Controller Link, SYSMAC LINK		S3200-CN[][][]-20-20	---
		S3200-CN[][][]-20-25
		S3200-CN[][][]-25-25

Optical connectors for H-PCF Optical Cables with Connectors are adhesive polished.

Cable Length

The following cable lengths are available: 2 m, 5 m, 15 m, 20 m. For lengths of 21 m or more, contact your OMRON sales representative.

Model Numbers

Optical Connector Assembly Tool

Name	Applicable Unit	Model	Manufacturer	Standards
Optical Fiber Assembly Tool *	This tool is used on site for mounting crimp-cut connectors and hard plastic-clad silica optical fiber for optical transmission systems of SYSMAC C-series SYSBUS, SYSMAC LINK, and Controller Link.	CAK-0057	Sumitomo Electric Industries, Ltd.	---

* There is a risk of quality problems when using cables assembled by typical users, so we recommend purchasing 
   cables with preattached connectors or having a qualified technician assemble the cables.