Kontak Kami

KONTAK KAMI : Telpon : 02126071413 Hp/WhatsApp : 081212269831 Perwakilan Jakarta : Gedung LTC Glodok Lantai 1 Blok C30 No.31 Jl.Hayam Wuruk No.127 Jakarta , Indonesia

Senin, 22 Oktober 2018

OMRON CJ1W-MD263



CJ1W-MD263 DC Input/Transistor Output Unit (24 VDC 32 Inputs/32 Outputs)

Name32-point DC Input/32-point Transistor Output Unit with MIL Connectors (Sinking Outputs)
ModelCJ1W-MD263
Output section (CN1)Input section (CN2)
Rated Voltage12 to 24 VDCRated Input Voltage24 VDC
Operating Load 
Voltage Range
10.2 to 26.4 VDCOperating Input 
Voltage
20.4 to 26.4 VDC
Maximum Load 
Current
0.3 A/point, 1.6 A/common, 3.2 A/UnitInput Impedance5.6 kΩ
Maximum Inrush 
Current
3.0 A/point, 10 ms max.Input Current4.1 mA typical (at 24 
VDC)
Leakage Current0.1 mA max.ON Voltage/ON 
Current
19.0 VDC min./3 mA 
min. *2
Residual Voltage1.5 V max.OFF Voltage/OFF 
Current
5 VDC max./1 mA max.
ON Response 
Time
0.5 ms max.ON Response Time8.0 ms max. (Can be set 
to between 0 and 32 in 
the Setup.) *1
OFF Response 
Time
1.0 ms max.
No. of Circuits32 (16 points/common, 2 circuits)OFF Response Time8.0 ms max. (Can be set 
to between 0 and 32 in 
the Setup.) *1
FuseNone
External Power 
Supply
10.2 to 26.4 VDC, 30 mA min.No. of Circuits32 (16 points/common, 
2 circuits)
Number of 
Simultaneously 
ON Points
75% (24 points) (at 24 
VDC)
Insulation 
Resistance
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC)
Dielectric 
Strength
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 
10 mA max.
Internal Current 
Consumption
5 VDC 140 mA max.
Weight110 g max.
AccessoriesNone
Circuit 
Configuration
CN1 (OUT)CN2 (IN)
2056_sp_4_1
The signal names of the terminals are the 
device variable names. 
The device variable names are the names that 
use "Jxx" as the device name.
2056_sp_4_2
The signal names of the terminals are the 
device variable names. 
The device variable names are the names that 
use "Jxx" as the device name.
2056_sp_4_3
External 
connection and 
terminal-device 
variable diagram
CN1 (OUT)CN2 (IN)
2056_sp_4_4
Be sure to wire both terminals 23 and 24 
(COM0) of CN1. 
Be sure to wire both terminals 3 and 4 (COM1) 
of CN1. 
Be sure to wire both terminals 21 and 22 (+V) of 
CN1. 
Be sure to wire both terminals 1 and 2 (+V) of 
CN1. 
When wiring, pay careful attention to the polarity 
of the external power supply. The load may 
operate incorrectly if polarity is reversed. 
The signal names of the terminals are the 
device variable names. 
The device variable names are the names that 
use "Jxx" as the device name.
2056_sp_4_5
Be sure to wire both pins 23 and 24 (COM2) of 
CN2, and set the same polarity for both pins. 
Be sure to wire both pins 3 and 4 (COM3) of 
CN2, and set the same polarity for both pins. 
When wiring, pay careful attention to the polarity 
of the external power supply. The load may 
operate incorrectly if polarity is reversed. 
The signal names of the terminals are the 
device variable names. 
The device variable names are the names that 
use "Jxx" as the device name.
With MIL connector (40-pin × 2)
CJ1W-MD263
CJ1W-MD563

CJ1W-MD Dimensions 6

Tidak ada komentar:

Posting Komentar