FX3U-232ADP-MB

Spesifications

• Manufacturer: Mitsubishi Electric 

• RS-232C for communication special adapter (MODBUS corresponding) FX3U-232ADP-MB
• Transmission standard : RS-232C compliant 
• Insulation method : Photocoupler 
• Transmission distance : Up to 15m 
• External device connection method : D-SUB 9Pin connector (male) 
• Communication system : Full-duplex bi-directional 
• Communication procedure : · MODBUS communication (master or slave) - No-protocol communication , computer link (dedicated protocol format 1, dedicated protocol format 4) programming communication 
• communication speed MODBUS communication : 300/600/1200/2400/4800/9600/19200/38400/57600/115200 (bps) corresponds to 38400/57600 / 115200bps from products manufactured on or after July 2012. (Serial number: 127 **** or later) 
• No-protocol communication, computer link : 300/600/1200/2400/4800/9600/19200/38400 (Bps) FX3U, FX3UC is, later Ver.2.41, it supports 38400bps. 
• Programming communication : 9600/19200/38400/57600/115200 (bps) 
• Display (LED) : RD, SD, POWER 
• O occupied points : 0 points (no relation to the maximum input and output points of the sequencer) 
• Apply sequencer : [FX3S]
  V1.00 and later: corresponding to all the communication function
  [FX3G]
  V1.00 and later: communication functions other than the MODBUS communication to the corresponding
  V1.30 and later: corresponds to the MODBUS communication function
  [FX3U]
  V2.20 and later: other than MODBUS communication communication function to the corresponding of
  V2.40 and later: corresponds to the MODBUS communication function
  [FX3GC]
  V1.40 and later: corresponding to all the communication function
  [FX3UC]
  V1.00 and later: corresponds to the communication functions other than the MODBUS communication
  V2.40 and later: MODBUS corresponding to the communication function  
• connection to FX3S is required FX3S-CNV-ADP.
  Connection to the FX3G is required FX3G-CNV-ADP.
  FX3U, connection to the FX3UC-32MT-LT (-2), you must have the function expansion board. 
• mass : 0.08kg 
• Power Specifications :   
• Power supply : DC5V 30mA (internal power supply from the sequencer) 
• Ambient temperature : 0 ~ 55 °C ····· operation, -25 ~ 75 °C ····· during storage 
• Relative humidity : 5 ~ 95% RH (non-condensing) ...... operation 
• Vibration resistance When the DIN rail mounting Frequency: 10 ~ 57Hz Half amplitude: 0.035mm X, Y, Z each direction 10 times (for a total of each 80 minutes) 
• Frequency: 57 ~ 150Hz Acceleration: 4.9m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes) 
• Direct mounting at the time Frequency: 10 ~ 57Hz Half amplitude: 0.075mm X, Y, Z each direction 10 times (for a total of each 80 minutes) 
• Frequency: 57 ~ 150Hz Acceleration: 9.8m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes) 
• Impact : 147m / s2, duration of action 11ms, X at half-sine pulse, Y, Z directions 3 times each 
• Anti-noise : Noise voltage 1,000Vp-p, noise width 1μs, due to rising 1ns, cycle 30 ~ 100Hz of noise simulator 
• Withstand voltage : D-SUB 9Pin connector and between the ground terminal of the basic unit: AC500V 1 minute 
• Insulation resistance : D-SUB 9Pin connector and between the ground terminal of the basic unit: DC500V 5MΩ more in insulation resistance tester 
• Use atmosphere : Corrosive, there is no flammable gas, conductive dust (dust) that is not terribly 
• Advanced use : 2000m or less
  can not be used in the pressurized environment to more than atmospheric pressure. There is a possibility of failure. 
• Shipping Weight: 1 Kg