Jumat, 13 April 2018

MITSUBISHI MR-JE-100A

MR-JE-100A Mitsubishi JE Series Servo Amplifier Model MR-JE AC servo drive

Combinations of Servo Amplifier and Servo Motor

Amplifier	Servo Motor		Stocked Item
	HG-KN Series	HG-SN Series
MR-JE-10B/MR-JE-10A	HG-KN13J	-	S
MR-JE-20B/MR-JE-20A	HG-KN23J	-	S
MR-JE-40B/MR-JE-40A	HG-KN43J	-	S
MR-JE-70B/MR-JE-70A	HG-KN73J	HG-SN52J	S
MR-JE-100B/MR-JE-100A	-	HG-SN102J	S
MR-JE-200B/MR-JE-200A	-	HG-SN152J HG-SN202J	S
MR-JE-300B/MR-JE-300A	-	HG-SN302J	S

Servo Amplifier Model MR-JE-		10A	20A	40A	70A	100A	200A	300A
Stocked Item		S	S	S	S	S	S	S
Output	Rated Voltage	3-phase 170 VAC
Output	Rated Current (A)	1.1	1.5	2.8	5.8	6.0	11.0	11.0
Power Supply Input	Voltage/Frequency (*1)	3-phase or 1-phase 200 VAC to 240 VAC, 50 Hz/60 Hz				3-phase 200 VAC to 240 VAC, 50 Hz/60 Hz
	Rated Current (A) (*7)	0.9	1.5	2.6	3.8	5.0	10.5	14.0
	Permissible Voltage Fluctuation	3-phase or 1-phase 170 VAC to 264 VAC				3-phase 170 VAC to 264 VAC
	Permissible Frequency Fluctuation	±5% maximum
Interface Power Supply		24 V DC ± 10% (required current capacity: 0.3 A)
Control Method		Sine-wave PWM control/current control method
Tolerable Regenerative Power of the Built-In Regenerative Resistor (W) (*2, 3)		-	-	10	20	20	100	100
Dynamic Brake		Built-in (*4)
Communication Function		USB: Connect a personal computer (MR Configurator2 compatible) RS-422: Connect a controller (1:n communication up to 32 axes) (*6)
Encoder Output Pulse		Compatible (A/B/Z-phase pulse)
Analog Monitor		2 channels
Position Control Mode	Maximum Input Pulse Frequency	4 Mpulses/s (when using differential receiver), 200 kpulses/s (when using open-collector)
	Positioning Feedback Pulse	Encoder resolution: 131072 pulses/rev
	Command Pulse Multiplying Factor	Electronic gear A/B multiple, A: 1 to 16777215, B: 1 to 16777215, 1/10 < A/B < 4000
	Positioning Complete Width Setting	0 pulse to ±65535 pulses (command pulse unit)
	Error Excessive	±3 rotations
	Torque Limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Speed Control Mode	Speed Control Range	Analog speed command 1:2000, internal speed command 1:5000
	Analog Speed Command Input	0 V DC to ±10 VDC/rated speed (Speed at 10 V is changeable with [Pr. PC12].)
	Speed Fluctuation Rate	±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%) ±0.2% maximum (ambient temperature: 25 °C ± 10 °C) only when using analog speed command
	Torque Limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Torque Control Mode	Analog Torque Command Input	0 VDC to ±8 VDC/maximum torque (input impedance: 10 kΩ to 12 kΩ)
Torque Control Mode	Speed Limit	Set by parameters or external analog input (0 V DC to ± 10 V DC/rated speed)
Servo Function		Advanced vibration suppression control II, adaptive filter II, robust filter, auto tuning, one-touch tuning, tough drive function, drive recorder function, machine diagnosis function, power monitoring function, lost motion compensation function.
Protective Functions		Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, overspeed protection, error excessive protection
Compliance to Standards		EN 61800-3, EN 61800-5-1, RoHS compliant, UL: UL 508C, KC compliant
Structure (IP Rating)		Natural cooling, open (IP20)					Force cooling, open (IP20)
Close Mounting		Possible (*5)
Environment	Ambient Temperature	0 °C to 55 °C (non-freezing), storage: -20 °C to 65 °C (non-freezing)
	Ambient Humidity	90 %RH maximum (non-condensing), storage: 90 %RH maximum (non-condensing)
	Ambience	Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
	Altitude	1000 m or less above sea level
	Vibration Resistance	5.9 m/s² at 10 Hz to 55 Hz (directions of X, Y and Z axes)
Weight (kg)		0.8	0.8	0.8	1.5	1.5	2.1	2.1

MITSUBISHI MR-JE40A

MR-JE40A Mitsubishi JE Series 400W Servo MR-JE AC servo drive 3-phase 200 VAC to 240 VAC Original adn New

Combinations of Servo Amplifier and Servo Motor

Amplifier	Servo Motor		Stocked Item
	HG-KN Series	HG-SN Series
MR-JE-10B/MR-JE-10A	HG-KN13J	-	S
MR-JE-20B/MR-JE-20A	HG-KN23J	-	S
MR-JE-40B/MR-JE-40A	HG-KN43J	-	S
MR-JE-70B/MR-JE-70A	HG-KN73J	HG-SN52J	S
MR-JE-100B/MR-JE-100A	-	HG-SN102J	S
MR-JE-200B/MR-JE-200A	-	HG-SN152J HG-SN202J	S
MR-JE-300B/MR-JE-300A	-	HG-SN302J	S

Servo Amplifier Model MR-JE-		10A	20A	40A	70A	100A	200A	300A
Stocked Item		S	S	S	S	S	S	S
Output	Rated Voltage	3-phase 170 VAC
Output	Rated Current (A)	1.1	1.5	2.8	5.8	6.0	11.0	11.0
Power Supply Input	Voltage/Frequency (*1)	3-phase or 1-phase 200 VAC to 240 VAC, 50 Hz/60 Hz				3-phase 200 VAC to 240 VAC, 50 Hz/60 Hz
	Rated Current (A) (*7)	0.9	1.5	2.6	3.8	5.0	10.5	14.0
	Permissible Voltage Fluctuation	3-phase or 1-phase 170 VAC to 264 VAC				3-phase 170 VAC to 264 VAC
	Permissible Frequency Fluctuation	±5% maximum
Interface Power Supply		24 V DC ± 10% (required current capacity: 0.3 A)
Control Method		Sine-wave PWM control/current control method
Tolerable Regenerative Power of the Built-In Regenerative Resistor (W) (*2, 3)		-	-	10	20	20	100	100
Dynamic Brake		Built-in (*4)
Communication Function		USB: Connect a personal computer (MR Configurator2 compatible) RS-422: Connect a controller (1:n communication up to 32 axes) (*6)
Encoder Output Pulse		Compatible (A/B/Z-phase pulse)
Analog Monitor		2 channels
Position Control Mode	Maximum Input Pulse Frequency	4 Mpulses/s (when using differential receiver), 200 kpulses/s (when using open-collector)
	Positioning Feedback Pulse	Encoder resolution: 131072 pulses/rev
	Command Pulse Multiplying Factor	Electronic gear A/B multiple, A: 1 to 16777215, B: 1 to 16777215, 1/10 < A/B < 4000
	Positioning Complete Width Setting	0 pulse to ±65535 pulses (command pulse unit)
	Error Excessive	±3 rotations
	Torque Limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Speed Control Mode	Speed Control Range	Analog speed command 1:2000, internal speed command 1:5000
	Analog Speed Command Input	0 V DC to ±10 VDC/rated speed (Speed at 10 V is changeable with [Pr. PC12].)
	Speed Fluctuation Rate	±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%) ±0.2% maximum (ambient temperature: 25 °C ± 10 °C) only when using analog speed command
	Torque Limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Torque Control Mode	Analog Torque Command Input	0 VDC to ±8 VDC/maximum torque (input impedance: 10 kΩ to 12 kΩ)
Torque Control Mode	Speed Limit	Set by parameters or external analog input (0 V DC to ± 10 V DC/rated speed)
Servo Function		Advanced vibration suppression control II, adaptive filter II, robust filter, auto tuning, one-touch tuning, tough drive function, drive recorder function, machine diagnosis function, power monitoring function, lost motion compensation function.
Protective Functions		Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, overspeed protection, error excessive protection
Compliance to Standards		EN 61800-3, EN 61800-5-1, RoHS compliant, UL: UL 508C, KC compliant
Structure (IP Rating)		Natural cooling, open (IP20)					Force cooling, open (IP20)
Close Mounting		Possible (*5)
Environment	Ambient Temperature	0 °C to 55 °C (non-freezing), storage: -20 °C to 65 °C (non-freezing)
	Ambient Humidity	90 %RH maximum (non-condensing), storage: 90 %RH maximum (non-condensing)
	Ambience	Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
	Altitude	1000 m or less above sea level
	Vibration Resistance	5.9 m/s² at 10 Hz to 55 Hz (directions of X, Y and Z axes)
Weight (kg)		0.8	0.8	0.8	1.5	1.5	2.1	2.1

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Mitsubishi Electric Servo Motors are made to high standards and offer a wide range of power, speed and inertia ratings providing a motor for all applications. Ranging from 50W through to 55kW and with specialist type motors available (flat "pancake"motors) the new Super Series Servo Motors complete the line-up of products offered by Mitsubishi Electric.

Also, all motors in the Mitsubishi Electric Super Series are fitted with absolute encoders as standard.Therefore, an absolute system can be created by simply providing power to Servo amplifier via a battery. Once this has been done the super capacitor inside the motor and back-up battery allow the Servo motor position to be constantly monitored, even when disconnected from the system.

Specification Overview

Type	Features	Application example
K	Type K (0.16 ~ 2.4Nm) Larger motor inertia moment makes this unit well suited for machines with fluctuating load inertia moment or machines with low rigidity such as conveyors.	LCD and conveyors Food preparation machinery Printers Small loaders and unloaders Small robots and component assembly devices Small X-Y tables Small press feeders
M	Type M (0.16 ~ 2.4Nm) Small motor inertia moment makes this unit well suited for high-frequency operation directly connected to ball screw components.	Inserters, mounters, bonders Printed board hole openers In-circuit testers Label printers Knitting and embroidery machinery Ultra-small robots and robot tips
S	Type S (2.4 ~ 33.4Nm) Stable control is performed from low to high speeds, enabling this unit to handle a wide range of applications.	Conveyor machinery Specialised machinery Robots Loaders and unloaders Winders and tension devices Turrets X-Y tables Test devices
R	Type R (3.18 ~ 15.8Nm) A compact sized low-inertia moment model with medium capacity. Well suited for high-frequency operation.	Roll feeders Loaders and unloaders High-frequency conveyor machinery

MITSUBISHI HF-KN23J-S10

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

Type	Features	Application example
K	Type K (0.16 ~ 2.4Nm) Larger motor inertia moment makes this unit well suited for machines with fluctuating load inertia moment or machines with low rigidity such as conveyors.	LCD and conveyors Food preparation machinery Printers Small loaders and unloaders Small robots and component assembly devices Small X-Y tables Small press feeders
M	Type M (0.16 ~ 2.4Nm) Small motor inertia moment makes this unit well suited for high-frequency operation directly connected to ball screw components.	Inserters, mounters, bonders Printed board hole openers In-circuit testers Label printers Knitting and embroidery machinery Ultra-small robots and robot tips
S	Type S (2.4 ~ 33.4Nm) Stable control is performed from low to high speeds, enabling this unit to handle a wide range of applications.	Conveyor machinery Specialised machinery Robots Loaders and unloaders Winders and tension devices Turrets X-Y tables Test devices
R	Type R (3.18 ~ 15.8Nm) A compact sized low-inertia moment model with medium capacity. Well suited for high-frequency operation.	Roll feeders Loaders and unloaders High-frequency conveyor machinery

MITSUBISHI HF-SP102B

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

Type	Features	Application example
K	Type K (0.16 ~ 2.4Nm) Larger motor inertia moment makes this unit well suited for machines with fluctuating load inertia moment or machines with low rigidity such as conveyors.	LCD and conveyors Food preparation machinery Printers Small loaders and unloaders Small robots and component assembly devices Small X-Y tables Small press feeders
M	Type M (0.16 ~ 2.4Nm) Small motor inertia moment makes this unit well suited for high-frequency operation directly connected to ball screw components.	Inserters, mounters, bonders Printed board hole openers In-circuit testers Label printers Knitting and embroidery machinery Ultra-small robots and robot tips
S	Type S (2.4 ~ 33.4Nm) Stable control is performed from low to high speeds, enabling this unit to handle a wide range of applications.	Conveyor machinery Specialised machinery Robots Loaders and unloaders Winders and tension devices Turrets X-Y tables Test devices
R	Type R (3.18 ~ 15.8Nm) A compact sized low-inertia moment model with medium capacity. Well suited for high-frequency operation.	Roll feeders Loaders and unloaders High-frequency conveyor machinery

Kamis, 12 April 2018

MITSUBISHI HF-SP52

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

Type	Features	Application example
K	Type K (0.16 ~ 2.4Nm) Larger motor inertia moment makes this unit well suited for machines with fluctuating load inertia moment or machines with low rigidity such as conveyors.	LCD and conveyors Food preparation machinery Printers Small loaders and unloaders Small robots and component assembly devices Small X-Y tables Small press feeders
M	Type M (0.16 ~ 2.4Nm) Small motor inertia moment makes this unit well suited for high-frequency operation directly connected to ball screw components.	Inserters, mounters, bonders Printed board hole openers In-circuit testers Label printers Knitting and embroidery machinery Ultra-small robots and robot tips
S	Type S (2.4 ~ 33.4Nm) Stable control is performed from low to high speeds, enabling this unit to handle a wide range of applications.	Conveyor machinery Specialised machinery Robots Loaders and unloaders Winders and tension devices Turrets X-Y tables Test devices
R	Type R (3.18 ~ 15.8Nm) A compact sized low-inertia moment model with medium capacity. Well suited for high-frequency operation.	Roll feeders Loaders and unloaders High-frequency conveyor machinery

AUTOMATION JAYA

Kontak Kami

Jumat, 13 April 2018

MITSUBISHI MR-JE-100A

MITSUBISHI MR-JE40A

MITSUBISHI HF-KE43BW1-S1

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

MITSUBISHI HF-KN23J-S10

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

MITSUBISHI HF-SP102B

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview

Kamis, 12 April 2018

MITSUBISHI HF-SP52

Servo Motors HC-KFS/ HC-MFS/ HC-SFS/ HC-RFS

Specification Overview