OMRON CJ1W-MD263

CJ1W-MD263 DC Input/Transistor Output Unit (24 VDC 32 Inputs/32 Outputs)

Name	32-point DC Input/32-point Transistor Output Unit with MIL Connectors (Sinking Outputs)
Model	CJ1W-MD263
Output section (CN1)		Input section (CN2)
Rated Voltage	12 to 24 VDC	Rated Input Voltage	24 VDC
Operating Load  Voltage Range	10.2 to 26.4 VDC	Operating Input  Voltage	20.4 to 26.4 VDC
Maximum Load  Current	0.3 A/point, 1.6 A/common, 3.2 A/Unit	Input Impedance	5.6 kΩ
Maximum Inrush  Current	3.0 A/point, 10 ms max.	Input Current	4.1 mA typical (at 24  VDC)
Leakage Current	0.1 mA max.	ON Voltage/ON  Current	19.0 VDC min./3 mA  min. *2
Residual Voltage	1.5 V max.	OFF Voltage/OFF  Current	5 VDC max./1 mA max.
ON Response  Time	0.5 ms max.	ON Response Time	8.0 ms max. (Can be set  to between 0 and 32 in  the Setup.) *1
OFF Response  Time	1.0 ms max.
No. of Circuits	32 (16 points/common, 2 circuits)	OFF Response Time	8.0 ms max. (Can be set  to between 0 and 32 in  the Setup.) *1
Fuse	None
External Power  Supply	10.2 to 26.4 VDC, 30 mA min.	No. of Circuits	32 (16 points/common,  2 circuits)
		Number of  Simultaneously  ON Points	75% (24 points) (at 24  VDC)
Insulation  Resistance	20 MΩ min. between the external terminals and the GR terminal (at 100 VDC)
Dielectric  Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of  10 mA max.
Internal Current  Consumption	5 VDC 140 mA max.
Weight	110 g max.
Accessories	None
Circuit  Configuration	CN1 (OUT)	CN2 (IN)
	The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.	The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.
External  connection and  terminal-device  variable diagram	CN1 (OUT)	CN2 (IN)
	Be sure to wire both terminals 23 and 24  (COM0) of CN1.  Be sure to wire both terminals 3 and 4 (COM1)  of CN1.  Be sure to wire both terminals 21 and 22 (+V) of  CN1.  Be sure to wire both terminals 1 and 2 (+V) of  CN1.  When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if polarity is reversed.  The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.	Be sure to wire both pins 23 and 24 (COM2) of  CN2, and set the same polarity for both pins.  Be sure to wire both pins 3 and 4 (COM3) of  CN2, and set the same polarity for both pins.  When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if polarity is reversed.  The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.

With MIL connector (40-pin × 2)
CJ1W-MD263
CJ1W-MD563

OMRON CJ1W-MD261

CJ1W-MD261 DC Input/Transistor Output Unit (24 VDC 32 Inputs/32 Outputs)

Name	32-point DC Input/32-point Transistor Output Unit with Fujitsu Connectors (Sinking Outputs)
Model	CJ1W-MD261
Output section (CN1)		Input section (CN2)
Rated Voltage	12 to 24 VDC	Rated Input Voltage	24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC	Operating Input Voltage	20.4 to 26.4 VDC
Maximum Load Current	0.3 A/point, 1.6 A/common, 3.2 A/Unit	Input Impedance	5.6 kΩ
Maximum Inrush Current	3.0 A/point, 10 ms max.	Input Current	4.1 mA typical (at 24 VDC)
Leakage Current	0.1 mA max.	ON Voltage/ON Current	19.0 VDC min./3 mA min. *2
Residual Voltage	1.5 V max.	OFF Voltage/OFF Current	5 VDC max./1 mA max.
ON Response Time	0.5 ms max.	ON Response Time	8.0 ms max. (Can be set to between 0 and 32 in the Setup.) *1
OFF Response Time	1.0 ms max.
No. of Circuits	32 (16 points/common, 2 circuits)	OFF Response Time	8.0 ms max. (Can be set to between 0 and 32 in the Setup.) *1
Fuse	None
External Power Supply	10.2 to 26.4 VDC, 30 mA min.	No. of Circuits	32 (16 points/common, 2 circuits)
		Number of Simultaneously ON Points	75% (24 points) (at 24 VDC)
Insulation Resistance	20 MΩ min. between the external terminals and the GR terminal (at 100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Internal Current Consumption	5 VDC 140 mA max.
Weight	110 g max.
Accessories	None
Circuit  Configuration	CN1 (OUT)	CN2 (IN)
	The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.	The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.
External  connection and  terminal-device  variable diagram	CN1 (OUT)	CN2 (IN)
	Be sure to wire both terminals A19 and A9  (COM0 (0 V)) of CN1.  Be sure to wire both terminals B19 and B9  (COM1 (0 V)) of CN1.  Be sure to wire both terminals A20 and A10 (+V)  of CN1.  Be sure to wire both terminals B20 and B10 (+V)  of CN1.  When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if polarity is reversed.  The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device name.	Be sure to wire both pins A9 and A18 (COM2) of  CN2, and set the same polarity for both pins.  Be sure to wire both pins B9 and B18 (COM3) of  CN2, and set the same polarity for both pins.  When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if polarity is reversed.  The signal names of the terminals are the  device variable names.  The device variable names are the names that  use "Jxx" as the device namel

With Fujitsu-compatible connector (40-pin × 2)
CJ1W-MD261

MITSUBISHI Q172DLX

Brand: MITSUBISHI 

Name: Servo external signal interface module

Model: Q172DLX

Input points: servo external signal 32 points, 8 axis.

Input mode: source / drain type.

Input and output points: 32 points.

Convenient processing of large capacity data.

In the past can not achieve the standard RAM and SRAM card file register area of continuous access,

The boundary of each area should be considered in programming.

The SRAM 8MB extension card is installed in the high speed universal QCPU,

Standard RAM can be used as a continuous file register,

Capacity up to 4736K words, thus simplifying the programming.

Thus, even if the memory space of the soft element is insufficient,

Can also be installed by the expansion of SRAM card, easy to extend the file register area.

The address register is extended to 32 bits, which can be programmed to go beyond the traditional 32K word,

And to achieve the extension to the file register to all regions of the file register.

In addition, the processing speed of the index modification plays an important role in the efficient operation of structured data (array),

The speed has been improved.

When the index is used to modify the program repeatedly (e.g. from FOR to NEXT), the scan time can be reduced.

GI-50/125 optical cable.

Double ring.

Remote I/O net (remote master station).

MELSECNET/H network module capable of composing large scale flexible network system.

The MELSECNET/H network system includes the PLC network of the control station and the communication between the stations and the remote I/O network in the remote station remote I/O station MITSUBISHI Q172DLX. 

Optical fiber loop system. Q172DLX.... High speed communication of 10Mbps/25Mbps is realized.

The distance between stations, the length of the total cable length, strong anti-interference.

Coaxial bus system...... Using low cost coaxial cable, the network construction cost is lower than that of the optical fiber loop network.

Twisted pair bus system MITSUBISHI Q172DLX. ..... Combined with high performance price ratio network module and twisted pair cable,

The construction cost of network system is very low.PCI bus /PCI-X bus.

Support Japanese, English OS.

Multimode fiber optic cable.

Dual loop controller network (control station / common station).

DB A20 AnyWire system uses a separate transmission mode,

Sensor networks to achieve high speed and high reliability MITSUBISHI Q172DLX. 

The transmission distance of 50m/200m/1km/3km can be selected.

1 modules can be up to 512 points of the input, 512 points of output (standard setting).

Even branch wiring, but also to detect transmission lines.

Province distribution network module in cabinet and device.

Link to connect the 64 stations when the fastest scanning time for 1 MITSUBISHI Servo external signal interface module. 2ms (rate 2.5Mbps).

According to the transmission distance, the transmission rate is selected from 2 MITSUBISHI Servo external signal interface module. 5Mbps, 625kbps and 156kbps.

CC-Link/LT from the station does not need any parameter settings.

Only need to set up the transmission speed in the master module, you can use the remote I/O.

I/O control in the first class of open field network module.

CC-Link based on reliable field bus technology,

Able to transmit large number of bits data (such as ON/OFF information) and word data (such as analog information) MITSUBISHI Servo external signal interface module Q172DLX.  

Consistency of CC-Link to maintain loop transmission,

And the cycle of transmission and information (instantaneous transmmission) communication separately, so as to ensure the timeliness of MITSUBISHI Q172DLX. 

Even if the information reaches saturation, it will not affect the link scan time.

MITSUBISHI MR-J2-40A

Brand: MITSUBISHI 

Name: Universal interface driver

Model: MR-J2-40A

MITSUBISHI general purpose AC servo amplifier MR-J2 series.

Rated output: 0.4kw.

Interface: general purpose interface.

Voltage: single phase AC200V.

MITSUBISHI servo system in the MITSUBISHI servo amplifier is widely used,

It can not only be used in the high precision position control and speed control of the working machinery and general industrial machinery,

Can also be used in the field of speed control and tension control.

By installing a personal computer with a servo setting software, the parameters setting, trial run, state display, and gain adjustment are performed.

MITSUBISHI servo system MR-J2S column is developed on the basis of the servo MR-J2 series with a higher performance and more features of the MITSUBISHI servo system,

The control modes are position control, speed control and torque control, as well as the switching control mode among them. 

Motor series: low inertia, small capacity.

Using a serial absolute / incremental encoder.

Rated output power: 0.05kw.

Rated speed: 3000rpm.

With the brake: not with brake.

Without GB.

Shaft end: straight shaft.

A servo motor is an engine that controls the operation of the mechanical components in the servo system MITSUBISHI MR-J2-40A. 

Servo motor can make the control speed, position accuracy is very accurate, can be converted to torque and speed voltage signals to drive the control object MR-J2-40A

Servo motor rotor speed is controlled by the input signal, and can quickly response,

In the automatic control system, used as actuators, and electromechanical time constant, high linearity, initiating voltage characteristics,

The signal can be converted into a motor shaft on the angular displacement or angular velocity output MITSUBISHI MR-J2-40A. 

Divided into DC and AC servo motor two major categories, the main features are,

When the signal voltage is zero, there is no rotation,

The speed increases with the increase of the torque and the speed decreases. Type: HA-SH series.

Rated output: 1.2KW.

Rated speed: 1000r/min.

Electromagnetic brake: there MITSUBISHI MR-J2-40A. 

From the vector control technology of AC servo motor, it has become more and more popular.

From the point of view of the real time operating system, it is just a function module that needs to be processed in real time.

Due to the multi function of the controller, intelligent requirements, a large number of signal processing,

Establishment and operation of various mathematical models of adaptive control,

Network communications and other functional modules will be in the real-time operation of the unified scheduling and management of the system to get the correct and reliable operation MITSUBISHI Electric machinery MITSUBISHI Electric machinery.  

Therefore, the next generation of servo drive controller will be a collection of various modern control technology of the crystallization,

Instead of the traditional sense of power amplifier MITSUBISHI Electric machinery. Cable length: 10m.

For MR-J2S-700A (4) /CP/CL or less.

Encoder for HC-KFS; HC-MFS; 3000r/min HC-UFS servo motor.

-H products have a long flex life. "MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.

Rated output: 3.5kw.

Built in positioning function.

Voltage: 3 phase AC200VAC or single phase AC230V.

Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Liink

Simply setting the point table MR-J2-40A. 

AC servo can be used as the driving source of the field network.

Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.

Start, stop and dissplay can also be transmitted through the CC-Link MITSUBISHI MR-J2-40A. 

Serial communication reduces wiring.

AC servo distributed control system can be easily constructed. "

MITSUBISHI MR-J3-10A

Brand: MITSUBISHI 

Name: Universal pulse interface driver

Model: MR-J3-10A

MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.

Rated output: 0.1kw.

Interface type: general pulse interface type.

Power specification: single phase AC200V.

Pulse train and analog input as universal interface.

Can choose the position, speed and torque control mode.

The use of advanced tuning features such as advanced vibration suppression control and adaptive filter,

Greatly improve the performance of the machine.

MR-J3, your partner.

Higher performance, more features, more convenient to use.

Highest performance in the industry.

Speed response frequency up to 2.1kHz. 

Type: MR-C type.

Symbol 10A for motor models: HC-PQ033/053/13.

Power supply voltage: single phase AC220V.

Drive: servo drive in the development of the premise of the frequency conversion technology,

Current loop in the drive,

Speed loop and position loop (frequency converter without the ring) have carried out a more precise control than the general frequency control technology and algorithm,

In function is also a lot stronger than the traditional servo,

The main point can be precise position control MITSUBISHI MR-J3-10A MR-J3-10A 

The control speed and position are controlled by the pulse sequence transmitted by the upper controller,

The internal algorithm of the driver and the faster and more accurate calculation and better performance of electronic devices to make it more superior to the inverter MITSUBISHI MR-J3-10A. Servo motor series: low inertia, medium / high power.

Rated output: 6.0kw.

Rated speed: 1000r/min.

Electromagnetic brake: with.

Shaft end specification: Standard (straight axis).

Voltage: 400V level.

Features: low inertia has low medium and high speed three models, suitable for different applications as a standard, 30KW and above servo motor can be installed flange or bracket MITSUBISHI MR-J3-10A. 

IP level: IP44.

Application example:

1, injection molding machine.

2, semiconductor manufacturing equipment.

3, large material handling system.

4, stamping machine.

Abundant motor product line can optimize the performance of the machine MITSUBISHI Low inertia medium power motor. 

Has a rich motor product line including a rotary servo motor, linear servo motor and direct drive motor MITSUBISHI Low inertia medium power motor. MITSUBISHI universal AC servo amplifier MELSERVO-JE series.

Rated output: 0.2kw.

Interface: SSCNETIII/H.

Compatible motor: HG-KN23J-S100, HG-KN23BJ-S100.

Superior basic performance and advanced ease of use, to promote the process of equipment servo.

MR-JE-B support servo network.

Advanced performance and ease of use MITSUBISHI Low inertia medium power motor. 

In order to allow you to build advanced drive control system,

MITSUBISHI motor will provide you with a full range of servo amplifier, servo motor, programmable controller, positioning module, display, and even advanced solutions.

In the global support system, including the purchase of products to the after-sales service, the performance of MELSERVO-JE will play to the extreme in the world.

Support servo system network SSCNETIII/H.

Can achieve the system of high response speed, multi axis, the performance of the synchronization, the line of the line MR-J3-10A. 

In addition, the encoder can be used as an absolute position encoder in a servo motor.

The absolute position detection system.

At the same time, the high performance of the equipment ccan be realized by the simple movement module, such as the mark detection, the electronic cam, the advanced synchronization control function and so on MITSUBISHI MR-J3-10A.

HMI MITSUBISHI GT2710-VTWD

Brand: MITSUBISHI 

Name: 10.4 inch touch screen

Model: GT2710-VTWD

Function: high performance and low price in the middle end model.

Picture size: 10.4 inches.

Resolution: VGA.

Display: TFT color.

Panel color: white.

Power type: DC24V.

The highest level model with multi touch and gesture features.

Specification rich, design at ease.

GT27 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.

Even in the log, script, alarm, soft component data transmission, such as high load processing period, but also to achieve smooth operation of the screen.

In addition, also supports video, animation playback, video input and RGB input and output, can use all the features of GOT2000.

Can be programmed CPU and other procedures, parameters, such as data storage (backup) to the SD GOT memory card, USB memory.

When the programmable controller fails, batch write back (recovery) program.

1, the human body sensor

People will be able to automatically detect and display the picture.

2, USB interface: device USB (Mini-B USB)

Can connect to the computer to transfer data.

3, USB interface: host USB (USB-A)

GOT data can be transmitted through the USB memory or read log data and other data,

Can also be connected to the USB mouse, keyboard use.

4, the extension of the interface

Communication module and optional module can be installed.

5, Ethernet interface

Up to 4 different manufacturers can be connected to the FA machine.

6, RS-232 interface

Can connect all kinds of FA machine, bar code reader, serial printer.

7, RS-422/485 interface

Can be connected to a variety of FA machines, bar code reader.

8, SD memory card slot

Can save alarm and log data, such as a large number of data. 

For the GT1675M-VTB.

Applicable model: GT16. Application: you can transfer the same image data at a high speed (about two seconds per 64KB data) to multiple F940GOT.

When programming software is used in the case of Designer2 GT,

You can create a file in HEX Intel format.

Using communication software to transfer data to a ROM writer MITSUBISHI GT2710-VTWD. 

Application Series: F940GOT. "Series introduction: with a variety of integrated functions and communication interface, and a larger volume of the basic model GT2710-VTWD

Screen size: 10.4 inches.

Display color: 256 color or more color.

Mounting type: panel mounting type.

Resolution: VGA (640 x 480).

Display device: TFT color.

Host frame color: black.

Power type: DC24V.

Communication interface: with built-in RS-422 MITSUBISHI GT2710-VTWD. 

With a variety of integrated functions and communication interface and a larger volume of the basic model.

User storage capacity: 6MB.

Device USB interface.

Standard Ethernet, RS-422/485 and RS-232 interface.

Analog touch panel.

From the technical principle to distinguish the touch screen, can be divided into five basic types: vector pressure sensor touch screen, resistive touch screen, capacitive touch screen technology, infrared touch screen technology, surface acoustic wave touch screen technology MITSUBISHI GT2710-VTWD. 

Vector pressure sensing technology touch screen has been withdrawn from the stage of history;

Infrared touch screen technology and low price, but the frame is fragile, easy to produce light interference and surface distortion;

The design of capacitive touch screen is reasonable, but it is difficult to solve the problem of image distortion;

The touch screen positioning resistor technology is accurate, but its price is high, and fear of vulnerability scratch;

The surface acoustic wave touch screen solves various defects of the touch screen in the past,

Clear and not easy to be damaged, suitable for various occasions,

The disadvantage is that the screen surface if there is water droplets and dust will make the touch screen become slow, or even work MITSUBISHI 8 MITSUBISHI 8 MITSUBISHI 8.4 Inch Touch Screen. 4 Inch Touch Screen. 4 Inch Touch Screen. "Function: high performance and low price in the middle end model.

Picture size: 10.4 inches.

Resolution: VGA.

Display: TFT color.

Panel color: white.

Power type: AC100~240V.

Middle end model of high performance and low price.

GT25 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.

Even in the log, script, alarm, soft component data transmission, such as high load processing period, but also to achieve smooth operation of the screen.

Connect GOT front USB interface and computer,

Can be through the FA, the GOT machine programming, start and adjust the operation,

Save the trouble of opening the control cabinet and changing the cable.

1, USB interface: device USB machine (Mini-B USB)

Can connect to the computer to transfer data.

2, USB interface: host USB (USB-A)

USB data can be transmitted through the USB memory or read log data, such as the GOT data, but also can be connected to the use of the mouse, keyboard.

3, the extension of the interface

Communication module and optional module cann be installed GT2710-VTWD. 

4, Ethernet interface

Up to 4 different manufacturers can be connected at the same time

FA machine.

5, RS-232 interface

Can connect all kinds of FA machine, bar code reader, serial printer.

6, RS-422/485 interfface

Can be connected to a variety of FA machines, bar code reader MITSUBISHI GT2710-VTWD. 

7, SD memory card slot

Can save alarm and log data, such as a large number of data.

MITSUBISHI AJ65SBTC1-32T

Brand: MITSUBISHI 

Name: Fast connector type transistor output module

Model: AJ65SBTC1-32T

Output type: transistor output, drain type.

Output points: 32 points.

OFF leakage current: 0.25mA.

Output protection function.

Rated load voltage / current: DC24V/DC24V/0.1A.

External connection: 1 wire.

Fast connector type.

Simple wiring through quick connector.

Can be installed along the 6 direction.

MITSUBISHI PLC program simulation debugging

The basic idea of program simulation debugging is,

In order to facilitate the form of simulation to generate the actual state of the scene,

Create the necessary environmental conditions for the operation of the program.

Depending on the way the field signals are generated,

The simulation debugging has two forms of hardware simulation and software simulation.

Input type: DC input, positive public end / negative public end.

Input points: 8 points.

Enter the response time: 10ms the following.

Rated input voltage / current: DC24V/7mA.

Output form: relay output.

Output points: 8 points.

OFF leakage current: -.

Output protection function: No.

Rated load voltage / current: DC12V/AC240V/2A MITSUBISHI AJ65SBTC1-32T. 

External connection: 2 line /2 line type.

Type of input and output terminal AJ65SBTC1-32T

Using 2 pieces of structure of the terminal units, maintenance can be maintained in the same line under the condition of the replacement module. Input type: DC input, positive public end / negative public end.

Input points: 4 points.

Input response time: 0.5ms below /1.5ms.

Rated input voltage / current: DC24V/4mA MITSUBISHI AJ65SBTC1-32T. 

External connection: 2 wire.

Spring clip terminal.

Do not need to re tighten, suitable for wire specifications for 0.3~1.5MM square.

Terminal block is 2 piece structure.

An input module shared by the common terminal of the positive and negative.

The 8 point of the output module is appended to the source type.

Can be installed along the 6 direction. Input type: DC input, positive common end MITSUBISHI AJ65SBTC1-32T. 

Input points: 8 points.

Enter the response time: 0.2ms the following.

Rated input voltage / current: DC24V/5mA.

External connection: 3 wire.

Fast connector type.

Simple wiring through quick connector.

Can be installed along the 6 direction.

MITSUBISHI PLC program simulation debugging

The basic idea of program simulation debugging is,

In order to facilitate the form of simulation to generate the actual state of the scene,

Create the necessary environmental conditions for the operation of the program MITSUBISHI Fast connector type transistor output module MITSUBISHI Fast connector type transistor output module. 

Depending on the way the field signals are generated,

The simulation debugging has two forms of hardware simulation and software simulation. Input type: DC input, positive public end / negative public end MITSUBISHI Fast connector type transistor output module. 

Input points: 16 points.

Enter the response time: 1.5ms the following.

Rated input voltage / current: DC24V/7mA.

External connection: 1 wire AJ65SBTC1-32T. 

According to the external connection mode and the external equipment input and output specifications,

Choose from a rich product lineup.

Finger protection through the upper part of the terminal,,

The human body will not be exposed to live parts,

Therefore, the terminal station type remote I/O module can be directly mounted to the machine tool MITSUBISHI AJ65SBTC1-32T.

MITSUBISHI QJ61BT11

Brand: MITSUBISHI 

Name: CC-Link module

Model: QJ61BT11

Master / local station sharing.

Corresponding Ver2 CC-Link.

Consistency of CC-Link to maintain loop transmission,

And the cycle of transmission and information (instantaneous transmission) communication separately, so as to ensure the timeliness of.

Even if the information reaches saturation, it will not affect the link scan time.

The QJ61BT11N module supports CC-Link version 1 and version 2, which can be used as a local station or master station module.

I/O control in the first class of open field network module.

CC-Link based on reliable field bus technology,

Able to transmit large number of bits data (such as ON/OFF information) and word data (such as analog information).

Input / output points: 4096 points.

Number of input and output elements: 8192.

Program capacity: 260 K step.

Processing speed: 0.0095 s.

Program memory capacity: 1040 KB.

Support USB and RS232.

Support installed memory card.

Providing high speed communication between multiple CPU.

Shorten the fixed scan interrupt time, high precision device MITSUBISHI QJ61BT11. 

The minimum interval of the fixed period interrupt program is reduced to 100 s QJ61BT11

The high speed signal can be accurately obtained, which makes the contribution to the higher precision of the device.

High speed and high precision machine control by multi CPU.

By parallel processing of the linear and multi CPU high-speed communication (cycle 0.88ms) of the parallel control program, the high speed control MITSUBISHI QJ61BT11. 

Multi CPU high speed communication cycle and motion control synchronization, so it can achieve the maximization of computing efficiency.

In addition, the latest movement control CPU in performance is 2 times the previous model,

To ensure high speed and high accuracy of the machine control.Input / output points: 4096 points.

Number of input and output elements: 8192 MITSUBISHI QJ61BT11. 

Program capacity: 60 K step.

Processing speed: 0.0095 s.

Program memory capacity: 240 KB.

Support USB and RS232.

Support installed memory card.

Providing high speed communication between multiple CPU.

High speed and high precision data processing MITSUBISHI CC-Link module. 

The processing speed of the real number (floating point) arithmetic has been greatly improved,

Addition instruction reached 0 MITSUBISHI CC-Link module. 014 mu s,

Therefore, it can support the request of high-speed, high-precision processing data processing.

In addition, the new addition of double precision floating point arithmetic instructions,

Simplify the programming, reduces the computational error when executing complex formula.

Shorten the fixed scan interrupt time, high precision device MITSUBISHI CC-Link module. 

The minimum interval of the fixed period interrupt program is reduced to 100 s.

The high speed signal can be accurately obtained, which makes the contribution to the higher precision of the device.Input: 2 channels.

Input: thermocouple / micro voltage / voltage / current.

Conversion speed (input):25ms/2 channel.

Sampling period: 25ms/2 channel.

Output: DC4~20mA.

Conversion speed (output):25ms/2 channel.

18 point terminal station.

With 5 kinds of PID control mode.

Loop control module suitable for fast response object control, such as temperature control, flow control, etc..

The loop control module has a PID control format and a sampling period of 25ms that is proportional to the speed,

Support high precision, high resolution Thermocouple Input, micro voltage input, voltage input, current input and current output.

The most suitable for high speed lift and temperature control and pressure control, flow control and other requirements of the application of high speed response.

Can be connected with JIS, IEC, NBS, ASTM standard thermocouple.

Through the small voltage, voltage, current input sensor, can be measureed in a variety of input range of analog QJ61BT11. 

Provides the program control function, can according to the specific requirements of the time automatically change the target value (SV) and PID constant [proportional band (P), integratiion time (I), differential time (D)],

And cascade control function, allowing channel 1 as the main station, channel 2 for the control from the station MITSUBISHI QJ61BT11.